Butt Weld Pipe Fittings ANSI B16.9 Tolerance




Butt Weld Pipe Fittings ANSI B16.9 Tolerance

 
All Fittings[Note(1) and (2)] Center-to-End Diamensions Overall Length of Reducers and Lap Joint Stub Ends,F,H Overall Length of Caps, E 180-deg Returns
Nominal  Pipe Size(NPS) DN Outside Diameter at Bevel,D[Note(3) and (4)] Inside Diameter at End [Note(3) and (5)] 90-deg and 45-deg Long and Short Radius Elbows and Tees. A,B,C,M 3D Radius Elbows, A,B Center-to-Center Dimension, O Back-to-Face Demensoin, K Alignment of Ends, U
 1/2to2 1/2 15-65  +1.6-0.8 0.8 2 3 2 3 6 6 1
3to3 1/2 80-90 1.6 1.6 2 3 2 3 6 6 1
4 100 1.6 1.6 2 3 2 3 6 6 1
5to8 125-200  +2.4 -1.6 1.6 2 3 2 6 6 6 1
10to18 250-450  +4.0 -3.2 3.2 2 3 2 6 10 6 2
20to24 500-600  +6.4 -4.8 4.8 2 3 2 6 10 6 2
26to30 650-750  +6.4 -4.8 4.8 3 6 5 10
32to48 800-1200  +6.4 -4.8 4.8 5 6 5 10
All Fittings[Note(1) and (2)] Center-to-End Diamensions Nominal Pipe Size(NPS) DN Angularity Tolerance
Nominal  Pipe Size(NPS) DN Outside Diameter at Bevel,D[Note(3) and (4)] Inside Diameter at End [Note(3) and (5)] Outside Diameter of Lap,G Fillet Radius of Lap,R Lap Thickness Off Angle,Q Off Plane,P
 1/2to2 1/2 15-65  +1.6-0.8 0.8 +0,-1 +0,-1 +1.6,-0 1/2to4 15-100 1 2
3to3 1/2 80-90 1.6 1.6 +0,-1 +0,-1 +1.6,-0 5to8 125-200 2 4
4 100 1.6 1.6 +0,-1 +0,-2 +1.6,-0 10to12 250-300 3 5
5to8 125-200  +2.4 -1.6 1.6 +0,-1 +0,-2 +1.6,-0 14to16 350-400 3 6
10to18 250-450  +4.0 -3.2 3.2 +0,-2 +0,-2 +3.2,-0 18to24 450-600 4 `10
20to24 500-600  +6.4 -4.8 4.8 +0,-2 +0,-2 +3.2,-0 26to30 650-750 5 10
26to30 650-750  +6.4 -4.8 4.8 32to42 800-1050 5 13
32to48 800-1200  +6.4 -4.8 4.8 44to48 1100-1200 5 19
GENERAL NOTES:
(a)All dimensions are in mm.
(b)Tolerances are equal plus and minus except as noted.
NOTES:
(1)The inside diameter and the nominal wall thickness at ends are to be specified by the purchaser.
(2)A minimum wall thickness of 87.5% applies unless the purchaser specifies a different wall thickness toletance.
(3)Out-of-round is the sum of absolute values of plus and minus tolerances.
 

Share this post

Related News